No.1 Индустриальный парк Гаода,
Фэнган, Дунгуань, Китай

inquiry@scondar.com

Photocopier Wire Harness Design: Connector Selection Guide for Office Equipment

Photocopier Wire Harness Design: Connector Selection Guide for Office Equipment

Application Context & Design Challenge

Modern office photocopiers and multifunctional printers (MFPs) are dense, high-performance machines that route dozens of signal and power connections across multiple sub-assemblies: ADF (Automatic Document Feeder) sensor arrays, imaging drum units, fuser heating elements, high-voltage power supplies, operation panel displays, and network interface boards. Each of these subsystems introduces distinct connector challenges.

At SCONDAR, we have worked with office equipment manufacturers to supply wire-to-board connectors for photocopier internal harnesses across multiple production generations. The recurring design challenges we observe in this category fall into three broad areas:

  • Signal density vs. available PCB real estate: Engineers must route 10–40 signal lines (sensor arrays, panel controls) through a confined chassis. Connectors must provide high contact count in a narrow footprint. Dual-row headers with 1.25mm–2.0mm pitch strike the right balance.
  • Mixed signal and power requirements: Copy machines handle both low-current sensor signals (≤1A) and moderate-power loads such as heating elements and motors (up to 3A). Selecting mismatched connectors for these different circuits risks either undersizing for power or wasting space on over-specified connectors.
  • Assembly process compatibility: High-volume photocopier production typically uses automated wire processing: fully automatic crimping machines for power and signal wires, and in some cases IDC (Insulation Displacement Contact) terminations for rapid sensor cable assembly. Connector housings must be compatible with both termination methods.

SCONDAR Connector Matching for Photocopier Applications

SCONDAR supplies footprint-compatible alternatives for the most widely adopted connector series used in office equipment manufacturing. The following product families cover the three main connection zones inside a typical photocopier wire harness:

Signal & Sensor Connections – SCT1252 (Hirose DF13 Compatible)

The SCT1252 series is footprint-compatible with the Hirose DF13 connector series, one of the most common signal-level connectors found in photocopier sensor and control circuits. Key design features relevant to office equipment:

  • 1.25mm pitch, single-row (2–15 positions) and dual-row (up to 2×20 positions) configurations
  • Scoop-proof box header structure prevents mis-insertion during field service—a practical concern for copiers under maintenance
  • SMT header with metal fittings for solder joint stress relief, addressing vibration fatigue in high-cycle office environments
  • Vacuum absorption area on headers supports Pick & Place automated assembly
  • Operating temperature range: -40°C to +85°C
  • Rated 1A per contact, suitable for sensor signals and low-power control lines
  • AWG #28–#32 wire compatibility matches typical hookup wires used in sensor extension cables

Dual-Row Signal & Display Bus – SCT2011 (Hirose DF11 Compatible)

For operation panels and display interface boards inside photocopiers, the SCT2011 series provides a dual-row footprint-compatible replacement for Hirose DF11. At only 5mm width with a 2×15 contact configuration, it doubles signal density within the same PCB footprint as a single-row connector. Relevant features:

  • 2.0mm pitch, dual-row from 2×2 to 2×15 positions
  • Rated 3A per contact—well-suited for display backlight and panel power rails
  • 250V rating provides generous voltage margin for office equipment power distribution
  • Gold and tin plating options; gold plating recommended for low-current signal integrity in panel communication buses
  • Both SMT and through-hole configurations available
  • Crimp termination process is compatible with standard automated crimping equipment

High-Reliability Internal Connections – SCT1251 ( PicoBlade Compatible)

The SCT1251 series is footprint-compatible with PicoBlade connectors, widely specified in industrial and office equipment for its compact form factor. For photocopier applications, this series is particularly suited to ADF sensor wiring and internal wiring between boards:

  • 1.25mm pitch, 2–16 positions
  • Two-point contact design provides reliable electrical connection under high-vibration conditions, addressing mechanical shock from drawer-style paper tray operation
  • Friction lock mechanism ensures secure mating retention during copier transport and servicing
  • Gold-plated contact option delivers enhanced reliability in humid operating environments (common in office settings with variable climate control)
  • Operating temperature range: -40°C to +85°C
  • Rated 1A, compatible with AWG #28–#32 wires commonly used in sensor harnesses

IDC & Crimp Dual-Option – SCT2007 (TE AMP CT Compatible)

For manufacturers seeking production flexibility, the SCT2007 series offers a dual-termination connector compatible with TE AMP CT series. Both IDC and crimp terminations are supported using the same housing family:

  • 2.0mm pitch, single-row (2–15 positions) and dual-row (8–30 positions)
  • IDC option: enables rapid sensor cable assembly without dedicated crimping tooling— advantageous for short-run custom wire lengths in photocopier sub-assemblies
  • Crimp option: supports AWG #22–#26 wires for higher current-carrying capacity within the same connector family
  • Rated 3A per contact, suitable for power distribution to motor drivers and control boards
  • 250V rating, 1000V AC withstand voltage—safe for direct connection to photocopier power supply modules
  • UL/CSA certified, aligning with office equipment safety standards

Technical Specification Overview

The table below summarizes the key electrical and mechanical specifications for SCONDAR connector series used in photocopier wire harness applications.

Parameter SCT1252 SCT2011 SCT1251 SCT2007
Pitch 1,25 мм 2,0 мм 1,25 мм 2,0 мм
Номинальный ток 1A 3A 1A 3A
Номинальное напряжение 125V 250V 150V 250V
Temp. Range -40°C ~ +85°C -25°C ~ +85°C -40°C ~ +85°C -25°C ~ +85°C
Покрытие контактов Tin / Gold Tin / Gold Tin / Gold Tin / Gold

Design-In Considerations: Mechanical & Process

Wire Gauge Matching

All four connector series above are rated for AWG #28–#32 fine-strand hookup wire at signal-level currents (1A), with SCT2011 and SCT2007 additionally rated for AWG #22–#26 when used at 3A. When routing photocopier sensor arrays, use the finer gauge (AWG #28–#30) for maximum flexibility in tight cable routing channels around the imaging drum assembly. Reserve AWG #24–#26 for power branches feeding motors and heating elements.

Crimp vs. IDC Termination Selection

For photocopier harnesses built with automated crimping equipment, the SCT1252, SCT2011, and SCT2007 series are all compatible with standard semi-automatic and fully automatic crimping machines. Pull-out force testing on production samples should maintain consistent results within the 20N–30N range across wire sizes within specification.

For short-run custom cable assemblies or repair/hobby market applications, the SCT2007 IDC option eliminates the need for dedicated crimping tooling. The insulation displacement termination creates a gas-tight contact by piercing the wire insulation with twin U-slot contacts, with no stripping or soldering required.

Polarization and Anti-Misinsertion Design

All SCONDAR office equipment connector series feature fully shrouded headers with polarizing keys. During photocopier field service—when connectors are frequently unplugged and re-seated during maintenance—the scoop-proof housing prevents bent pins and mis-mating between adjacent connectors of different circuit functions.

Quality Assurance & Supply Chain

SCONDAR operates under ISO 9001:2015 quality management (Certificate No. 02816Q11592RS) and holds UL/CUL certification (E538921) for wire harness assemblies. All connector housings use PA66 or PBT raw material with UL94V-0 flammability rating, and all plating finishes comply with RoHS and REACH requirements as verified by SGS testing reports.

For photocopier manufacturers placing orders in the 1,000–50,000 unit range, SCONDAR offers standard lead times of 1–2 weeks for in-stock connector series, with free sample kit service available for design validation. We have successfully delivered interconnect solutions to over 2,000+ global electronics and industrial equipment manufacturers since 2008.

Frequently Asked Questions

How do I verify PCB footprint compatibility when replacing Hirose DF13 with SCT1252?

The SCT1252 series is designed as a footprint-compatible alternative to Hirose DF13, meaning the PCB mounting holes, header dimensions, and contact positions match the original specifications. Before production adoption, we recommend: (1) Cross-reference the SCONDAR product datasheet for exact dimensions—header height and pin protrusion should be confirmed against your PCB pad layout; (2) Request a free sample kit from SCONDAR to perform a fit-check on your current board revision; (3) Verify that the wire gauge you plan to use falls within the AWG #28–#32 range specified for this series.

Are these connectors suitable for continuous-duty operation in high-cycle office environments?

Yes. The contact system in all four connector series uses phosphor bronze base material with tin or gold plating, designed for repeated mating cycles. The SCT1251 two-point contact design is particularly effective at maintaining low contact resistance under vibration and repeated insertion/removal cycles. All series operate within their rated temperature range for standard office environments (-25°C to +85°C for most office equipment grades). For photocopiers installed in non-climate-controlled warehouses, the extended temperature grades of SCT1252 and SCT1251 (rated to -40°C) provide additional margin.

Inside an MFP, a single harness can carry sensor signals, panel power, and fuser control within a few centimeters of each other—so connector choice is as much about density and serviceability as electrical spec. If you’re mapping SCT1252, SCT2011, SCT1251, or SCT2007 onto your sub-assemblies and want to sanity-check footprint compatibility with the incumbent part, describe the circuit in the comments. Need to see it in hand first? Request samples, or send your existing BOM to ouroffice-equipment specialists. The full footprint-compatible set is in thewire-to-board portfolio.

Поделиться этим постом

Поделиться в facebook
Поделиться в reddit
Поделиться в twitter
Поделиться в linkedin
Поделиться в pinterest
Поделиться в print
Поделиться в vk
Поделиться в skype
Поделиться в email

Вопросы? Напишите нам!

Любой запрос или вопрос, предложение приветствуются, чем больше деталей сообщение с, тем быстрее ответ вы получите.

Контактная информация

No. 1, Gaoda Industrial Park, Shuibu Rd
Фэнган, Дунгуань, Китай (материк).

Социальные сети

Давайте поговорим